SKU: NXB-MNT-813-008 | Version: 1.0 | Brand: NexBot Robotics
NexBot Safety 813-008 Tool Adapter Plate ISO 9409-1-50-4-M6 (NXB-MNT-813-008) is a tool adapter plates used in industrial robotics equipment where category-specific fit, electrical or mechanical compatibility, and predictable serviceability are important to buyers. The product should be understood as the exact component named by its category path, not as a complete robot or a generic service item. It supports installation, replacement, and maintenance workflows in robotic production cells by giving procurement and maintenance teams a clearly defined part class, relevant engineering specifications, and application context that matches the actual hardware being purchased.
Verify the installed item is NexBot Safety 813-008 Tool Adapter Plate ISO 9409-1-50-4-M6 with SKU NXB-MNT-813-008. Cross-check the unit against project documentation before applying power or connecting it to the host system.
Understand how the product is used within the Accessories & Mounting > Brackets & Adapters > Tool Adapter Plates workflow, including any upstream and downstream dependencies, service intervals, and operator responsibilities.
Power up the unit under controlled conditions, observe indicator states, and verify the product initializes cleanly with the expected site-rated supply operating setup.
Run NexBot Safety 813-008 Tool Adapter Plate ISO 9409-1-50-4-M6 within the documented workload, environmental, and service conditions. Track alarms, unusual noise, heat, or vibration so corrective action can be scheduled before unplanned downtime occurs.
Use the supported electrical and control interfaces to commission, monitor, and troubleshoot the device. Validate all signal mappings and control behavior after maintenance or part replacement.
Keep the product within the published ratings for speed, force, load, and environmental exposure. Where applicable, confirm mounting, routing, and attached tooling do not compromise access, cooling, or serviceability.
Whenever hardware, firmware, wiring, or connected tooling changes, repeat the relevant verification and commissioning checks before returning the equipment to production service.
| Interval | Task | Notes |
|---|---|---|
| Daily | Inspect NexBot Safety 813-008 Tool Adapter Plate ISO 9409-1-50-4-M6 for visible wear, damage, contamination, loose hardware, and abnormal status indicators. | Record any abnormalities before the next production cycle begins. |
| Monthly | Verify mounting integrity, connector condition, and cable routing or strain relief points. | Retorque or reseat hardware only to the documented service specification. |
| Quarterly | Review diagnostic logs, event history, and operational trends for early signs of degradation. | Escalate recurring warnings before they develop into hard faults. |
| Annually | Perform a full service inspection covering mechanical condition, electrical connections, and functional verification. | Coordinate annual service with planned downtime to minimize production disruption. |
| Symptom | Possible Cause | Solution |
|---|---|---|
| Unit does not initialize or remain ready | Incoming supply, controls wiring, or commissioning parameters do not match the documented site-rated supply configuration. | Verify power quality, wiring continuity, protective devices, and startup parameters before restarting the unit. |
| Intermittent communication or status loss | Loose connectors, damaged cabling, or interface mismatch. | Inspect physical connections, confirm interface settings, and replace damaged cables or connectors as needed. |
| Unexpected wear, vibration, or overheating | Mechanical loading, contamination, misalignment, or duty cycle exceeds the intended application conditions. | Inspect the installation, restore proper alignment and cooling, and verify the product is being used within its published operating limits. |
| Connected equipment performance is inconsistent | The installed product is not configured correctly for the host system or compatible robot series (R-10, R-20, C-5). | Validate the configuration, confirm compatibility, and rerun the functional verification procedure after any corrections. |
| Parameter | Value | Unit |
|---|---|---|
| Weight | 0.28 | kg |
| Material | Aluminum 6061-T6, Black Anodized | |
| Country of Origin | JP | |
| Dimensions | 80 x 80 x 12 mm |