Installation Guide: NexBot Robotics 733-010 Cleaning Solvent, 1 Liter

SKU: NXB-GEN-733-010 | Revision: 1.0 | Category: Wear Parts & Consumables > Lubricants & Fluids > Cleaning Solvents

DANGER: Disconnect all power sources before beginning installation. Follow lockout/tagout (LOTO) procedures per OSHA 1910.147.

1. Required Tools & Materials

Nitrile or Butyl Rubber Gloves (Chemical Resistant)
Safety Goggles or Face Shield
Lint-Free Industrial Wipes
Nylon Bristle Brushes
Designated Solvent Application Container (Glass or HDPE)
Waste Container for Solvent-Soaked Materials
Adequate Mechanical Ventilation or Respirator
Fire Extinguisher (Class B)

2. Pre-Installation Checks

Verify the product is NexBot Robotics 733-010 Cleaning Solvent (SKU: NXB-GEN-733-010) and the container seal is intact.
Read the Safety Data Sheet (SDS) for NXB-GEN-733-010 before opening the container.
Ensure the work area is well-ventilated and free from ignition sources such as sparks or open flames.
Confirm all required Personal Protective Equipment (PPE) is available and in good condition.
Check the material compatibility of the component to be cleaned with the solvent. If unsure, test on a small, non-critical area first.
Power down and de-energize any electrical or robotic equipment to be cleaned, following proper lock-out/tag-out (LOTO) procedures.

3. Installation Procedure

Step 1: Step 1: Prepare the Work Area

Establish a designated cleaning zone. Ensure proper ventilation is active and a fire extinguisher is accessible. Lay down chemical-resistant matting if working on sensitive surfaces.

Warning: Vapors may be flammable. Prohibit smoking, welding, or any spark-generating activities in the vicinity.

Step 2: Step 2: Don Personal Protective Equipment (PPE)

Put on chemical-resistant gloves and safety goggles. If ventilation is inadequate, a respirator approved for organic vapors is required.

Step 3: Step 3: Open and Dispense Solvent

Carefully break the seal and open the 1.1 kg container. Pour a small, required amount of the 733-010 Cleaning Solvent into a designated application container to avoid contaminating the main supply.

Warning: Avoid splashing. In case of skin contact, wash immediately with soap and water. In case of eye contact, flush with water for 15 minutes.

Step 4: Step 4: Pre-Clean the Component

Remove loose dirt, debris, and heavy grease from the component surface using a dry cloth or brush. This improves the effectiveness of the solvent and prolongs its useful life.

Step 5: Step 5: Apply the Solvent

Using a lint-free wipe or nylon brush dipped in the solvent, apply a thin, even layer to the surface requiring cleaning. For stubborn contaminants, allow the solvent to sit for a short period as recommended in the equipment service manual, but do not let it dry completely on the surface.

Warning: Do not apply directly to powered electronics, unsealed bearings, or sensitive optical sensors.

Step 6: Step 6: Agitate the Surface

Gently agitate the surface with the brush or wipe to dislodge contaminants. Work systematically from the top of the component downwards.

Step 7: Step 7: Wipe Clean and Dry

Before the solvent evaporates, wipe the surface clean with a fresh, dry, lint-free cloth to remove the dissolved contaminants and excess solvent. For critical applications, a second wipe with a clean cloth may be necessary.

Warning: Ensure component is completely dry before re-energizing equipment to prevent electrical shorts or fire.

Step 8: Step 8: Dispose of Waste

Place all used wipes, brushes, and contaminated materials into a designated, sealed waste container. Dispose of the waste in accordance with local, state, and federal environmental regulations.

Warning: Solvent-soaked rags can be a fire hazard. Do not dispose of them in standard trash receptacles.

4. Post-Installation Verification

Visually inspect the cleaned component for any remaining residue or contaminants.
Confirm that the component surface is completely dry.
Verify that no solvent has dripped onto incompatible materials or sensitive equipment areas.
Check that the cap on the main 733-010 Cleaning Solvent container is tightly sealed to prevent evaporation.
Store the remaining solvent in a cool, dry, well-ventilated area away from direct sunlight and ignition sources.
Ensure all tools and PPE are cleaned and stored correctly.

Note: For technical support, contact your authorized service provider or visit https://robotics.barca.group/support.